Kasynets AI SolutionsBack to Kasynets AI Solutions

Engineering Proof of Concept

Warehouse Digital Twin 3D PRO

Interactive Operational Intelligence, Warehouse Simulation & Decision Support

Try your first scenario

Load the 150% demand scenario to start with 200 workers per shift, 15% fatigue, Shift 2, Strict mode and no fault. Then change staffing or simulate a failure and compare the estimates. Use Reset scenario to return to the baseline.

Compare two further one-day estimates. Each preset replaces all inputs: 100% demand, Shift 2 and Strict mode; the sorter scenario uses 200 workers and 15% fatigue, while the workforce scenario has no equipment fault.

Current illustrative scenario: demand 300,000 units/day; capacity 300,000 units/day; ending queue 14,200 units; net queue change +0.

What do the main indicators mean?

OMS: Order Management System; demand means new orders in this one-day scenario. Capacity: how much could be processed. Throughput: what is processed, limited by capacity and available work. Queue: opening backlog plus demand minus throughput.

OTIF: On Time In Full. SLA: Service Level Agreement. Both are represented here by an illustrative service estimate, not measured delivery performance. MHE: Material Handling Equipment, including the simulated forklifts. WMS: Warehouse Management System; this prototype is not connected to one.

Estimated Daily Throughput

300,000

units / day, capacity 300,000

OMS Order Queue

14,200

end-of-day units; opening 14,200, net change +0

Estimated OTIF / SLA

99.2%

On track, illustrative estimate

MHE Operations

Strict

4 forklifts, safety enabled

Cardboard Baler Utilization

72.0%

logical, ~274 illustrative cycles

Operational System Status

Nominal

No fault

Illustrative 10,000 square metre warehouse with Zone A picking, storage, sorters and dispatch; Zone B receiving and loading.

Touch: swipe to scroll the page. Enable touch controls to rotate or pinch the warehouse; exit to scroll again.

Illustrative 10,000 square metre warehouse. Approximately 50 representative worker markers shown, each standing for about four workers. Four forklifts run on marked paths and stop for proximity or equipment faults.

Camera: drag to rotate, scroll wheel to zoom, pinch with two fingers to zoom. Keyboard: arrow keys rotate, plus and minus zoom, 0 resets.

Stopped for worker proximity
0
Stopped for forklift proximity
0
Managed low-speed passing
0
Halted by MHE fault
0
Overhead cardboard belt
Running
Zone A (x < 60 m)Zone BPicking Operations and High-Bay Storage racksForklift floor pathSafety envelopeActual stopManaged low-speed movementCartons and balesFailed equipmentHydraulic Cardboard Baler1 worker marker is about 4 workers
How the estimate works — full methodology

The model assumes one unit per order and a full-day projection at the selected shift’s operating conditions. The opening queue is carried into the estimated end-of-day queue; these are scenario estimates, not a live WMS/OMS feed.

Capacity starts from a 300,000 unit daily baseline, scaled by staffing (power 0.84), fatigue, shift pattern, fault and MHE mode. Each scenario is a one-day estimate with the same opening queue of 14,200 units, not cumulative animation time. Throughput is the lower of capacity and new daily demand plus the opening queue. Ending queue = opening queue + new demand − processed throughput; net queue change = ending − opening. Negative change means backlog drawdown, not negative demand. There are no other arrivals or processing in this model.

For illustration, today's demand is processed first; spare capacity then draws down the opening queue. Capacity coverage divides capacity by new daily demand and can exceed 100%. Capacity utilization divides processed throughput by capacity and cannot exceed 100%. At 450,000 demand and 300,000 capacity, coverage is 66.7%, utilization is 100%, unmet demand is 150,000 and ending queue is 164,200 (+150,000).

OTIF is an illustrative estimate, not operational telemetry: 99.2% times processed demand coverage, minus a fatigue penalty, bounded 0 to 99.8%. The opening queue is carried as conserved backlog and does not lower OTIF by itself; this simplified allocation does not model real order priority or due dates.

Strict vs comparative MHE

Proximity checks stay active in both modes, including endpoint stops and fork lifting. After a proximity pause, separated routes can resume monitored low-speed passing; conflicting routes wait for coordinated clearance. Comparative uses a wider envelope and slower travel. Red means stopped; amber means managed low-speed movement. This is illustrative coordination, not certified collision avoidance or a recommendation for real-world safety settings.

Hydraulic Cardboard Baler utilization

The logical utilization comes from modelled cardboard flow. The hopper fill shown in the 3D view is cosmetic and can differ. Cycle counts are illustrative, not daily telemetry.

Workforce markers

Each marker stands for about four workers. The 600 worker baseline is three shifts of 200. Animated markers split roughly 52% picking, 24% sorter and 24% Zone B.

This interactive Digital Twin is an engineering proof of concept. Operational metrics, equipment behavior, and safety scenarios are illustrative and require validation against real-world WMS/OMS data.